bsncubed
e2dc7552c2
SAP, syslog and health/temperatures are done and verified. The VLAN split needs a tagged VLAN with DHCP on the switch and is only needed for the internet sources, so it moves to a phase 2 section. Step 4 notes what is still open (Riedel import, Wireshark). Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
58 lines
5.0 KiB
Markdown
58 lines
5.0 KiB
Markdown
# aes67-ESP32-P4
|
|
|
|
AES67 sender on a Waveshare ESP32-P4-ETH (PoE). Sources: Spotify Connect (cspot) and HLS/m3u8, with failover. Riedel-style web UI and a reusable AES67 core (PTP, RTP TX, SDP/SAP, VLAN, syslog, health) meant for later AES67 projects.
|
|
|
|
Repo: https://gitea.apointless.space/bsncubed/aes67-ESP32-P4
|
|
|
|
## Read first
|
|
- `docs/aes67-core-base.md`: reusable core. Config schema, API, PTP (roles, Riedel defaults, status fields), AES67 TX/SDP/SAP, VLAN, syslog, temperatures, component layout.
|
|
- `docs/hardware-and-design-notes.md`: board pinout, chip revision caveat, project pipeline (cspot/HLS), failover, player API.
|
|
- `web/index.html`: finished web UI (single file). It is the API contract; firmware must match the JSON it reads and writes.
|
|
|
|
## Working rules
|
|
- **One change at a time** ("one fuckup at a time"). Change or test one variable per step; never stack several fixes or hypotheses. If something breaks, go back to the last known-good state.
|
|
- Follow the build order below. Finish and verify a step on hardware before starting the next.
|
|
- After every change: `idf.py build`, flash, and check the serial monitor output. Show the relevant log lines.
|
|
- Don't mark a step done until it has been verified on the board.
|
|
- Keep core and project separate: `components/aes67_*` must not depend on `main/` (sources/player). Project code plugs in through the config, status and route registries.
|
|
- `web/index.html`: keep the CORE / PROJECT markers. If the firmware needs an API change, change the doc and the page together.
|
|
- Small, focused commits per step.
|
|
|
|
## Toolchain
|
|
- ESP-IDF 5.5 or later (needed for the P4 and for `examples/network/vlan_support`). Target `esp32p4`.
|
|
- `idf.py set-target esp32p4`, `idf.py build`, `idf.py -p <PORT> flash monitor`
|
|
- Before first build: run `esptool.py chip_id` and `esptool.py flash_id`.
|
|
- Chip revision < v3.0 (engineering silicon, seen on some of these boards) needs `CONFIG_ESP32P4_SELECTS_REV_LESS_V3=y`.
|
|
Our board: **v1.3** (set in sdkconfig.defaults, min rev v1.0).
|
|
- Our board: **32 MB** flash (GigaDevice c8/4019). App slots must stay below 16 MB (cache mapping above 16 MB is experimental in IDF).
|
|
- Embed `web/index.html` via `EMBED_TXTFILES` in `aes67_web`.
|
|
- Flash over the network (normal way since step 2b; keep USB for recovery):
|
|
`curl -f --data-binary @build/aes67_p4.bin -H 'Content-Type: application/octet-stream' http://p4-aes67/api/ota`
|
|
The board reboots into the new image on trial; check `GET /api/ota` shows the new version with `pending_verify: false`.
|
|
- Serial: opening /dev/ttyACM0 can reset the board. Don't open it while an OTA image is on trial (a reset then counts as a failed boot and rolls back).
|
|
- Rollback test build (self-test always fails), in its own build dir:
|
|
`idf.py -B build-selftest-fail -DSDKCONFIG=build-selftest-fail/sdkconfig -DSDKCONFIG_DEFAULTS="sdkconfig.defaults;sdkconfig.selftest_fail" build`
|
|
|
|
## Board quick reference (full details in docs)
|
|
- Ethernet: IP101GRI, RMII, PHY addr 1, ref clock from PHY into GPIO50 (EMAC_CLK_EXT_IN).
|
|
MDC 31, MDIO 52, PHY reset/power 51, TX_EN 49, TXD0 34, TXD1 35, CRS_DV 28, RXD0 29, RXD1 30.
|
|
- No Wi-Fi/BT on this board.
|
|
- On-die temperature sensor only (driver/temperature_sensor.h).
|
|
|
|
## Build order / status
|
|
- [x] 0. Check chip revision and flash size; create IDF project and empty component stubs (layout in aes67-core-base.md). Set up the OTA partition table (two app slots, no factory) and PROJECT_VER from git now, so the layout never changes later.
|
|
- [x] 1. Ethernet: IP101 up, DHCP, IP logged. Ping works.
|
|
- [x] 2. Web server + config store (cJSON in NVS) + embedded index.html; /api/config, /api/status (stub values), /api/reboot.
|
|
- [x] 2a. Finding the device: mDNS (hostname.local + _http._tcp), then LLDP (switch shows name + IP).
|
|
- [x] 2b. Firmware update: /api/ota upload + rollback self-test. Test: update to a new build, then deliberately flash a build that fails its self-test and confirm it rolls back. After this, flash over the network; keep USB for recovery.
|
|
- [x] 3. PTP TimeReceiver: lock to an existing GM (Riedel), fill `status.ptp`. Confirm EMAC hardware timestamps work. First check whether the installed ESP-IDF has a PTP example/component for the P4 before writing one.
|
|
- [ ] 4. AES67 TX with a 1 kHz test tone, PTP-paced; /stream.sdp. Verify: import SDP on a Riedel Artist 4-wire AES67 port, and check packets/timestamps in Wireshark.
|
|
Done and checked with a receiver script (all ptimes, L16/L24, tone phase-locked to PTP); still open: the Riedel import and a Wireshark capture.
|
|
- [x] 5. SAP discovery, then syslog, then health/temperatures (one at a time). VLAN split moved to phase 2.
|
|
- [ ] 6. PTP TimeTransmitter: BMCA roles (auto/master), hybrid mode.
|
|
- [ ] 7. Sources: HLS player, then cspot (Spotify Connect), then failover + /api/player.
|
|
- [ ] 8. Mono sum, gain, polish.
|
|
|
|
## Phase 2 (parked)
|
|
- [ ] VLAN split: AES67 untagged + internet tagged (inet.vlan_id/pcp), per aes67-core-base.md "Network". Needs a tagged VLAN with DHCP on the switch port. Config group `inet` and the UI fields exist already; nothing is applied yet.
|